Whirlpool Microwave Code E11: Gas Sensor Reported a Problem
E11 on a Whirlpool over-the-range microwave comes from the gas sensor, which has sent the control board a problem report. The sensor or its wiring may be at issue, and sensor cooking may not work.
What does Whirlpool microwave code E11 mean?
Owners of Whirlpool over-the-range microwaves, for example the WMH31017HS, WMH32519HZ and WMH53521HZ, may meet E11 when the gas sensor sends the control board a problem report. This sensor picks up steam and vapors while a sensor cooking program runs. Its own condition or its wiring could be the source. With E11 showing, programs that rely on the sensor may not work, but timed cooking could still run.
E11 at a glance
- Code
- E11
- Appliance
- Whirlpool microwave
- Applies to
- Whirlpool over-the-range microwaves with sensor cooking, WMH31017HS
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- A gas sensor that no longer returns a readable signal
What you may notice with E11
- E11 shows in the display of the over-the-range microwave.
- Sensor cooking programs refuse to run or stop early.
- Timed cooking may still work as normal.
How the microwave detects E11
Sensor cooking lets the microwave decide for itself when food is done. The gas sensor sits where it can sample steam and vapors from the food, and its readings tell the control how far along the cooking is. The control depends on those readings to run the program.
When the sensor reports a problem to the control board, E11 is the result. The sensor could have failed, the wiring that carries its signal could be damaged or loose, or the board's input could be misreading it. From outside, there is no telling the sensor from its wiring, so the control cannot name a part. It stops the programs that need the sensor and shows E11, while a plain timer cycle, which does not use the sensor, may carry on.
Likely causes of E11
- A gas sensor that no longer returns a readable signal
- A damaged or loose lead between the sensor and the board
- An input on the control board that misreads the sensor
Can you keep using the microwave with E11?
Timed cooking may still be fine while E11 is showing, and you can use it if the oven runs normally. Sensor programs are best avoided, since they depend on the very part that reported the problem. If the microwave stops heating, smells burnt or shows other codes, switch off the breaker and stop using it until it has been tested.
What you can safely check
- Stop the program; if you smell burning, turn the breaker off and leave the door shut.
- Let the breaker stay off for a minute, then restore power.
- Stay near the microwave for a minute to confirm E11 stays gone.
- Wipe the interior and vents clean and dry once the oven has cooled.
- Run a plain timed cycle. If E11 returns, avoid sensor programs and call us.
What our technician does for E11
- Test the circuit before naming a part
- Measure the signal the sensor circuit hands to the control
- Inspect the wiring between the sensor and the board
How to keep E11 from coming back
- Wipe steam and grease from the interior and the vents often, with the power off and the cavity cool.
- Cover foods that spatter heavily so vapor and grease do not coat the sensor area.
Technical reference
- Code
- E11
- Appliance
- Whirlpool microwave
- Control family
- Whirlpool over-the-range microwaves with sensor cooking, WMH31017HS
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Whirlpool models that can show E11
Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.
Related Whirlpool microwave error codes
E11 questions
What job does the gas sensor do in a microwave?
It senses humidity and vapor coming off the food so sensor cooking programs know when to stop. E11 tells you the control got a bad report from that sensor or its wiring.
Can I still warm food while E11 shows?
Timed cooking may still work, since it does not rely on the sensor. Skip the automatic programs for now. If nothing runs at all, the circuit needs a closer look.
Could a breaker reset clear E11?
A reset can remove a momentary glitch. If E11 returns after it, the sensor or its wiring has a lasting problem and needs testing.
Does E11 mean the sensor itself has failed?
Not necessarily. The guidance names the sensor or its wiring, so a loose or damaged lead could be to blame while the sensor is still sound. Testing the circuit shows which one it is.
What happens if I ignore E11 and keep using timed cooking?
Timed cooking may continue to work, but the sensor problem stays. Sensor programs will keep failing, and a connection that is loose can get worse over time, so it is better to have it tested.
Need help with E11?
We trace the cause in your home first and write the price down before any part is swapped.
