(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool Over-the-Range Microwave E03: Keypad Communication Problem

E03 means the keypad, also known as the user interface, sent a problem report to the control board of a Whirlpool over-the-range microwave. Either the keypad or its wiring could be responsible.

Needs attention soonChecked November 2026

What does Whirlpool microwave code E03 mean?

Owners of a WMH31017HS, WMH32519HZ or WMH53521HZ over-the-range microwave from Whirlpool may see E03, which means the keypad (the user interface) has sent the control board a problem report. The source could be the keypad itself or the wiring connecting it to the board. Alongside E03 in the display, certain buttons may stop responding, or a cycle may fail to start. Think of it as pointing at the keypad area, with no part yet proven bad.

E03 at a glance

Code
E03
Appliance
Whirlpool microwave
Applies to
Whirlpool over-the-range microwave keypad (e.g. WMH31017HS)
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
A keypad or user interface with failing pads

What you may notice with E03

  • The display reads E03 instead of the usual time.
  • Some buttons no longer respond when pressed.
  • A cooking cycle may refuse to start.

How the microwave detects E03

Every button press on an over-the-range Whirlpool microwave travels from the keypad, also called the user interface, to the control board along a ribbon of wiring. The board listens for those presses and for a healthy status report from the keypad itself.

E03 is displayed when that report is bad. The keypad may have a failing pad or circuit, the wiring between it and the board may be loose or damaged, or the board's input may be misreading an otherwise good keypad. From inside the oven, the board cannot tell which. It stops trusting the interface, which is why some buttons may go dead and a cycle may fail to start, and it shows the code to tell you the problem lies in the keypad area.

Likely causes of E03

  • A keypad or user interface with failing pads
  • Wiring between the keypad and the control board that has loosened or worn
  • A control board input that misreads the keypad

Can you keep using the microwave with E03?

If a reset removes E03 and every button works, the microwave can be used again, but a repeat is a warning. When the keypad is misbehaving, you may not be able to stop a cycle the way you expect. So if E03 returns, or buttons respond oddly, switch off the breaker and leave the oven alone until it has been tested.

What you can safely check

  1. Stop any cycle; if the oven smells burnt, switch off its breaker and keep the door shut.
  2. Leave the breaker off for one minute.
  3. If the keypad is greasy, wipe it lightly with a damp cloth while the power is still off.
  4. Restore power and stay close for a minute to see that E03 stays away.
  5. Try a short cycle to check that buttons and heating work. If E03 returns or buttons stay dead, call us.

What our technician does for E03

  • Find out whether the keypad or its wiring is the weak spot, which a reset cannot show
  • Check the keypad's connection to the control board
  • Examine the board input last, before replacing anything

How to keep E03 from coming back

  • Clean the keypad with a lightly dampened cloth, never a spray that can seep behind the pads.
  • Press buttons with a fingertip instead of a fingernail or a sharp object, which wears the pad surface.

Technical reference

Code
E03
Appliance
Whirlpool microwave
Control family
Whirlpool over-the-range microwave keypad (e.g. WMH31017HS)
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

Models

Whirlpool models that can show E03

Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.

FAQ

E03 questions

What is the keypad's job on this microwave?

The keypad takes your button presses and passes them to the control board. When the board receives a bad report from it, E03 is displayed, and some buttons may stop working.

Why would only some buttons stop working with E03?

A keypad in trouble can lose individual pads while others still respond. Testing the interface and its connection shows whether the pads themselves or the wiring behind them are responsible.

Is it fine to use the oven once a reset clears E03?

Yes, if E03 stays away and every button responds. If the code returns, do not lean on the keypad any longer and have the oven examined.

Is E03 a problem with the display or with the keypad?

The guidance points to the keypad, also called the user interface, or its wiring to the control board. The display shows the code, but it is not named as the cause.

Will E03 clear by itself after a power reset?

It may, if a passing glitch caused it. If E03 returns, the keypad circuit has a lasting problem. Note whether certain buttons stop working, since that detail helps narrow the cause.

Need help with E03?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair