(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool Over-the-range Microwave Code SE: A Keypad Circuit Report

SE on a Whirlpool over-the-range microwave points at the keypad, the user interface, or the wiring tied to it; the keys may not answer properly.

Needs attention soonChecked November 2026

What does Whirlpool microwave code SE mean?

Whirlpool over-the-range microwaves like the WMH53521HZ and WMH32519HZ display SE when something is wrong with the keypad, the user interface, or with its wiring. The screen shows SE and the keys may respond badly or not at all. What the code gives us is a circuit to test. A failed keypad is not yet proven by it.

SE at a glance

Code
SE
Appliance
Whirlpool microwave
Applies to
Whirlpool OTR microwave keypad circuit
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
The keypad itself, the user interface

What you may notice with SE

  • SE is showing on the display of the microwave
  • Keys respond slowly, wrongly or not at all
  • The code may vanish after a reset and then come back

How the microwave detects SE

A keypad is a set of pads that each send a signal to the control when pressed. The control listens for those signals through a connector between the keypad and the board behind it, and then acts on what you asked for.

SE is shown when something along that path is wrong. The keypad may have worn, so signals go missing or turn false. A wire or connector may have loosened, so signals fail to arrive. The control may also be reading the keypad incorrectly. From the display these look alike, which is why keys can seem dead or erratic while SE shows. A reset clears a passing confusion but cannot repair a worn keypad, so a repeat sends us to test the keypad and its connector before the control board.

Likely causes of SE

  • The keypad itself, the user interface
  • A wire or connector linking the keypad to the control
  • The way the control reads the keypad

Can you keep using the microwave with SE?

If a breaker reset clears SE and every key answers correctly, you can use the microwave and watch for a repeat. If the code returns or keys behave oddly, stop. A keypad that sends false signals can start or change a cycle you did not intend, a poor idea above a cooktop. Leave the unit off at the breaker until it has been tested.

What you can safely check

  1. Go to the panel and switch this microwave's breaker off, then wait a full minute.
  2. Turn it back on and watch the unit for a minute to see whether SE returns.
  3. Wipe the keypad using a dry cloth.
  4. If SE stays gone, run an ordinary cycle.
  5. If SE returns, or keys act strangely, stop using the microwave and contact us.

What our technician does for SE

  • Test the keypad and its connector ahead of the control board
  • Check how the control reads the keys

How to keep SE from coming back

  • Wipe the keypad with a dry cloth after cooking so grease and moisture do not settle on it.
  • Keep spray cleaners off the keypad, since liquid can run into the connection behind it.

Technical reference

Code
SE
Appliance
Whirlpool microwave
Control family
Whirlpool OTR microwave keypad circuit
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

Models

Whirlpool models that can show SE

Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.

FAQ

SE questions

Does SE prove the keypad is broken?

Not by itself. The code reports on the keypad circuit, which covers the keypad and its wires, so the keypad could be fine while a connection is the real culprit. Testing sorts that out.

May the microwave stay in use with SE?

Yes, provided a reset removes it and every key responds. If SE returns or keys misbehave, stop using the microwave until the circuit has been tested.

Is SE a cousin of F9Q1?

Both involve the touch pad, yet they are different codes. SE points at the keypad and its wiring, whereas F9Q1 is reported when the oven could not execute a function.

Could damp on the keypad bring up SE?

Moisture or grease can upset a keypad, so a dry wipe is a safe first step. If SE returns after that, the circuit needs a proper test rather than more cleaning.

Might SE clear itself?

A passing glitch may disappear after a power reset and stay away. If SE comes back, the keypad or its connection is still reporting trouble and should be tested.

Need help with SE?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair