Whirlpool Microwave Drawer Showing F7 E2: Level Sensor Circuit
F7 E2 on a Whirlpool built-in unit means the water level, its sensor, or the wiring between them has reported a problem.
What does Whirlpool microwave code F7 E2 mean?
The WMC50522AS and its Whirlpool built-in relatives may flash F7 E2 when the water level, the sensor watching it, or the wiring joining them reports trouble. F7 E0 carries identical guidance, yet F7 E2 is a separate code on your screen. Water-dependent functions refuse to run while it shows. The screen cannot separate a sensor from a harness or the control input, so diagnosis follows the circuit link by link.
F7 E2 at a glance
- Code
- F7 E2
- Appliance
- Whirlpool microwave
- Applies to
- Whirlpool WMC50522AS microwave drawer, level sensor circuit
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- A weak or missing signal from the level sensor
What you may notice with F7 E2
- F7 E2 shows on the display
- Functions that depend on water refuse to run
- The screen may clear after a reset and then show the code again
How the microwave detects F7 E2
A water-based function on these Whirlpool units depends on knowing the level of the water. The level sensor turns that level into a signal and sends it along a harness to the control, which reads the signal at an input on the board.
F7 E2 is raised when the control cannot get a usable reading from that chain. The water level itself may be wrong, the sensor may be sending a bad signal, a connector in the harness may have a poor contact, or the input that reads the signal may be failing. The control has no way to separate these from inside, so it stops the water-dependent functions rather than run them blind. A reset only shows whether the problem was momentary. A repeat sends us to test the signal at each link in the chain.
Likely causes of F7 E2
- A weak or missing signal from the level sensor
- A harness or plug in the sensor line with poor contact
- The control input that reads the level circuit
Can you keep using the microwave with F7 E2?
If F7 E2 is gone after a reset and the oven heats normally, use it while watching for a repeat. When the code returns, leave the water-dependent functions off until the circuit has been tested. Do not open the unit to look for the cause yourself. If water appears around the unit, switch the breaker off at once.
What you can safely check
- Flip this microwave's breaker off at the panel and leave the unit and its wiring alone.
- Allow a minute to pass.
- Bring power back and see whether F7 E2 shows within the next minute.
- A clear screen invites a normal cycle.
- If the code returns, stop the water-dependent functions and call us.
What our technician does for F7 E2
- Test the signal from the level sensor to the control
- Check connectors before parts
- Replace a part only when the test points to it
How to keep F7 E2 from coming back
- Keep spills and splashes away from the unit's control area so moisture does not reach connectors.
- Avoid repeated power cycling at the breaker while the code is showing, since it only masks the signal.
Technical reference
- Code
- F7 E2
- Appliance
- Whirlpool microwave
- Control family
- Whirlpool WMC50522AS microwave drawer, level sensor circuit
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool microwave error codes
F7 E2 questions
Why do these two level codes seem so similar?
F7 E0 and F7 E2 each lead to the level sensor and its cabling. They differ on the display, yet the guidance is shared, so one level-circuit test covers either.
Can the plain microwave function stay in use?
Yes, as long as one reset removes the message and the oven then behaves, while you keep watching. A returning code is the cue to pause until the unit is checked.
Is there anything inside I can look at?
No. Leave panels and the cabling behind them closed; flipping the breaker is all that you should do yourself.
Can F7 E2 clear without a repair?
A momentary signal problem can clear after a power reset. If F7 E2 reappears, the level circuit is still reporting trouble, and a test of the sensor, harness and control input finds which link is weak.
What do you need from me on the phone?
Tell us the code as shown, the model number such as WMC50522AS, and whether the code appeared during a water-based function. Mention it if anything was leaking.
Need help with F7 E2?
We trace the cause in your home first and write the price down before any part is swapped.