Whirlpool Microwave Error F4E4: Humidity Thermistor Check
A Whirlpool over-the-range microwave shows F4E4 when the control cannot read the humidity thermistor, the part that helps it sense moisture, or the wiring to it.
What does Whirlpool microwave code F4E4 mean?
F4E4 appears on over-the-range Whirlpool microwaves such as WMH31017HS, WMH32519HZ or WMH53521HZ when the control cannot read the humidity thermistor or the wires leading to it. That thermistor lets the microwave sense moisture in the cooking space. Whirlpool gives only a power reset, with no failed part named, so F4E4 prompts a test of the humidity sensor circuit.
F4E4 at a glance
- Code
- F4E4
- Appliance
- Whirlpool microwave
- Applies to
- Whirlpool over-the-range microwave humidity thermistor
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- Thermistor that senses humidity
What you may notice with F4E4
- F4E4 appears on the display of the over-the-range microwave
- Automatic sensing features may not run as usual
- The code may return after the reset
How the microwave detects F4E4
The humidity thermistor sits where the control can follow moisture in the cooking space, and automatic cooking uses what it reports. Like any thermistor, its resistance changes, and wiring and a plug bring that signal to the control board.
F4E4 is shown when the signal makes no sense to the control. The thermistor could be giving a wrong value, the wiring or plug could be breaking the signal, or the board input could be misreading it. The display does not separate these. The breaker reset Whirlpool lists restarts the control so that it reads the thermistor again. A circuit in order lets the display clear. A circuit with a problem sends F4E4 back, and then each link is tested in turn, from the thermistor to its plug to the control.
Likely causes of F4E4
- Thermistor that senses humidity
- Plug and wire serving the humidity sensor
- Input on the control board
Can you keep using the microwave with F4E4?
Wait for the display to clear. With F4E4 showing, the control cannot read the humidity thermistor properly, and the guidance does not say how the microwave behaves. Do the breaker reset once and run a short cycle. If all is normal, you may use the microwave and keep watch. If F4E4 returns, stop using it until the humidity sensor circuit has been tested.
What you can safely check
- If the microwave was just used, let it cool and dry, then switch off its breaker.
- Wait sixty seconds, then switch the breaker on.
- Watch the display for F4E4 over the following minute.
- If the display stays clear, run a quick cycle.
- Should F4E4 return, call us.
What our technician does for F4E4
- Check the humidity thermistor and its connector
- Test the control input that reads it
- Confirm the cause before replacing a part
How to keep F4E4 from coming back
- Let the microwave cool and dry after long, steamy cooking before the next cycle.
- Use the hood fan over the cooktop so steam does not collect around the microwave.
Technical reference
- Code
- F4E4
- Appliance
- Whirlpool microwave
- Control family
- Whirlpool over-the-range microwave humidity thermistor
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Whirlpool models that can show F4E4
Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.
Related Whirlpool microwave error codes
F4E4 questions
How does F4E4 differ from F3H?
Both codes involve humidity sensing on these models, and Whirlpool lists the humidity thermistor under each. We read which circuit the control is actually flagging when we test the microwave.
Can steam from the cooktop trigger F4E4?
Whirlpool lists no such cause. Allow the microwave to cool and dry, then use the breaker reset. A returning F4E4 means the circuit needs a test.
What happens when the microwave is looked at?
The humidity thermistor circuit is tested, the finding is explained, and a written price is given first. You decide whether to go ahead, and nothing is replaced until you agree.
Does F4E4 mean the microwave cannot sense moisture any more?
Not necessarily. The control has trouble with the humidity thermistor reading or the wires to it, and nothing more is stated. Whether automatic sensing is affected is not known, so the circuit is tested and the result explained.
Will F4E4 disappear if I just wait?
Waiting does not repair a sensor circuit. A reset may clear the display, but if the cause is still there the code returns, and the circuit then needs a proper test.
Need help with F4E4?
We trace the cause in your home first and write the price down before any part is swapped.
