(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool Microwave Error F3H1: Humidity Sensor Circuit

F3H1 on a Whirlpool over-the-range microwave tells us the control suspects the humidity sensor or the wires leading to it, and automatic features may not run as usual.

Needs attention soonChecked November 2026

What does Whirlpool microwave code F3H1 mean?

Over-the-range Whirlpool microwaves, models WMH31017HS, WMH32519HZ and WMH53521HZ among them, can display F3H1. It tells us the control suspects the humidity sensor or its wiring, and the microwave may not run its automatic features as usual. Whirlpool names no failed part and offers only a power reset. F3H1 therefore sends us to test the humidity sensor circuit, which is not the same as saying a sensor must be replaced.

F3H1 at a glance

Code
F3H1
Appliance
Whirlpool microwave
Applies to
Whirlpool over-the-range microwaves, WMH32519HZ among them
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Humidity sensing part

What you may notice with F3H1

  • F3H1 is showing on the microwave's front display
  • Automatic cooking features may not run as usual
  • The code may reappear after the breaker reset

How the microwave detects F3H1

On an over-the-range microwave with automatic cooking, a humidity sensor tells the control how much moisture is in the cooking space. The signal travels by wiring and a connector to an input on the control board.

The control compares that signal with what a working sensor should deliver. If the sensor, the connector or the input does not deliver it, the control shows F3H1 and may not run the automatic features as it usually does. The guidance does not point at one part. A power reset restarts the control, so it reads the sensor afresh. If the circuit is in order, the display stays clear. If not, F3H1 comes back, and each link in the circuit is tested in turn.

Likely causes of F3H1

  • Humidity sensing part
  • Lead and connector between the sensor and the board
  • Board input that reads the sensor

Can you keep using the microwave with F3H1?

Only if F3H1 clears after the reset and a short normal cycle works. In that case the microwave is fine to use, with a second appearance in mind. If F3H1 returns, do not use the microwave. The control is reporting a problem it cannot resolve, and it should stay off until the humidity sensor circuit has been tested.

What you can safely check

  1. Make sure the microwave is empty, then flip off its breaker.
  2. Wait for a full minute and flip it back on.
  3. Watch the display during the next minute for F3H1.
  4. If the display is clear, run a short ordinary cycle to check operation.
  5. If F3H1 appears again, leave the microwave off and call us.

What our technician does for F3H1

  • Test the humidity sensor
  • Check its connector and wiring
  • Test the control input, in that order

How to keep F3H1 from coming back

  • Wipe the cooking space dry after steamy cooking, with the microwave cool and switched off.
  • Cover dishes loosely so that heavy steam stays out of the sensor area.

Technical reference

Code
F3H1
Appliance
Whirlpool microwave
Control family
Whirlpool over-the-range microwaves, WMH32519HZ among them
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

Models

Whirlpool models that can show F3H1

Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.

FAQ

F3H1 questions

What separates F3H1 from F3H?

F3H points to the humidity thermistor and F3H1 to the humidity sensor on these models. The reset is the same for both, and we confirm the actual part by looking at the unit.

Could heavy steam from cooking trigger F3H1?

The brand names no such cause. Give the microwave time to cool and dry, then do the breaker reset. If F3H1 comes back, the circuit has to be tested.

Is it worth replacing the sensor on my own?

We would not advise it. The sensor is tucked inside the housing, and what the code names is a circuit; no part has been proven bad. Testing first spares you from buying something that is not the cause.

Does F3H1 mean the automatic features are broken?

Not exactly. The code says the control has a problem with the humidity sensor circuit, and automatic features may not run as usual. Whether the features themselves are damaged cannot be told from the code, so we test the circuit.

Will F3H1 go away if I wait?

Waiting does not repair a sensor circuit. A reset may clear the display, but if the cause is still there, the code comes back, and then the circuit needs a proper test.

Need help with F3H1?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair