(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool Built-In Microwave F01: Oven Temperature Sensor Circuit

F01 is the older display style of the oven temperature sensor message on Whirlpool built-in microwaves and drawers. Trouble could sit in the sensor, in the control, or in the wiring between them.

Needs attention soonChecked November 2026

What does Whirlpool microwave code F01 mean?

Whirlpool built-in microwaves and drawers of the older display style, WMC50522AS among them, can show F01 when the control finds trouble in the oven temperature sensor circuit. Three suspects share the blame: the sensor, the control, and the wiring running between them. The code does not prove that any of them has failed. Microwaves that show codes in this format tend to be several years old, and the oven may not heat, or a cycle may end early.

F01 at a glance

Code
F01
Appliance
Whirlpool microwave
Applies to
Whirlpool older-style built-in microwaves, WMC50522AS
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
A temperature sensor that reports the wrong value

What you may notice with F01

  • F01 shows in the display of the older-style built-in microwave.
  • The oven may not heat, or a cycle may stop early.
  • The same code may reappear after power is reset.

How the microwave detects F01

A microwave keeps track of its own temperature using a sensor, and the control reads the sensor's signal over a short run of wiring. That reading tells the control when heating is safe to continue and when a cycle should stop.

F01 is how the older display style reports trouble in that chain. The sensor could be reading wrongly, the control could be misinterpreting a good signal, or a connector between them could have worked loose. The control cannot see which, so it halts heating and puts the code on screen. After a power reset, a code that comes straight back shows the circuit still holds the problem, and that is the point where testing becomes necessary.

Likely causes of F01

  • A temperature sensor that reports the wrong value
  • A control that misreads a good sensor
  • A loose or damaged connector in the sensor circuit

Can you keep using the microwave with F01?

When a reset clears F01 and a brief test run heats as it should, you can keep using the oven while you watch for a repeat. If the code returns, set the microwave aside until it has been checked, because the temperature sensor circuit helps the control keep heating under control. Switch off the breaker straight away if you notice a burning smell.

What you can safely check

  1. Stop the cycle and let the cavity cool; switch off the breaker if you smell anything hot.
  2. Wait a full minute with the power off, then restore it.
  3. Observe the display for sixty seconds to see whether F01 reappears.
  4. Run a brief test to confirm the oven heats.
  5. If F01 comes back, leave the oven unused until it has been checked.

What our technician does for F01

  • Test the temperature sensor and the wiring that serves it
  • Check the control's input to separate a bad reading from a misreading board
  • Look for a loose connector when the code comes and goes

How to keep F01 from coming back

  • Leave the vents and the space around the microwave clear so heat does not collect near the sensor wiring.
  • Avoid knocking or tugging the microwave in its cabinet, since a jolted connector can set off the code.

Technical reference

Code
F01
Appliance
Whirlpool microwave
Control family
Whirlpool older-style built-in microwaves, WMC50522AS
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F01 questions

Which part of the oven does F01 point to?

The oven temperature sensor circuit, meaning the sensor, the control, and the wiring running between them. Nothing on the display tells you which of those three is at the root, so the whole circuit is tested.

Are F01, F02 and F1 separate problems?

No. Their guidance is identical for these models, so all three lead to the same circuit and the same tests. A different number does not mean a different part.

Can a power reset get rid of F01 permanently?

It can wipe out a momentary glitch, but a code that comes back means the circuit still has a real problem. At that point the sensor, the control and the wiring have to be tested.

Is F01 the same repair as F02?

The manufacturer gives the two codes the same guidance, so no separate part belongs to each number. The oven temperature sensor circuit is the shared area, and testing it covers both codes.

Is it harmful to ignore F01?

The control stops heating when it cannot trust the sensor circuit, so the oven protects itself. Even so, an oven that keeps showing F01 will not heat reliably, so testing the circuit makes more sense than resetting it repeatedly.

Need help with F01?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair