Whirlpool Over-the-Range Microwave F4E1: Cavity Thermistor Circuit
On a Whirlpool over-the-range microwave, F4E1 concerns the cavity temperature thermistor or the wiring to it, and it is not the same code as the F4 E1 shown by built-in models.
What does Whirlpool microwave code F4E1 mean?
Over-the-range Whirlpool microwaves such as WMH31017HS, WMH32519HZ or WMH53521HZ use F4E1 for the cavity temperature thermistor or the wires leading to it. The thermistor tells the control the temperature inside the cooking space. The display shows the code, with a power reset as Whirlpool's only step and no failed part named. For us F4E1 opens a sensor circuit test, and it should not be confused with F4 E1 on built-in models.
F4E1 at a glance
- Code
- F4E1
- Appliance
- Whirlpool microwave
- Applies to
- Whirlpool over-the-range microwave cavity thermistor
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- Thermistor measuring cooking space temperature
What you may notice with F4E1
- F4E1 shows on the display of the over-the-range microwave
- The microwave stops running as it normally does
- The code may come back after the breaker reset
How the microwave detects F4E1
A thermistor in the cooking space reports the temperature there to the control. Its resistance moves with the heat, and the control converts that into a reading through the thermistor lead and connector.
The control expects a believable figure. If the thermistor drifts, the lead or connector breaks the signal, or the control misjudges a good one, F4E1 shows on the display. The spaced code F4 E1 on built-in models belongs to a different circuit, so the two are checked differently. The power reset Whirlpool lists restarts the control and gives it a fresh reading. A sound circuit lets the display clear, while a circuit with a problem makes F4E1 return and calls for a test of the sensor circuit.
Likely causes of F4E1
- Thermistor measuring cooking space temperature
- Lead and connector for the thermistor
- Control that interprets the thermistor reading
Can you keep using the microwave with F4E1?
Only while the display is clear. The code means the control cannot read the temperature of the cooking space, so a cycle may not be regulated as it should. Do the reset once and then a short cycle. If everything behaves, you may use the microwave and keep watch. If F4E1 returns, keep it off until the cavity thermistor circuit has been tested.
What you can safely check
- Let the microwave cool, then turn its breaker off for sixty seconds.
- Turn it on again.
- Look at the display over the next minute for F4E1.
- If nothing shows, run a brief cycle and check that the microwave heats.
- If F4E1 comes back, leave the microwave unused and phone us.
What our technician does for F4E1
- Test the sensor circuit
- Compare the thermistor reading with what the control expects
- Check the connector and the control input
How to keep F4E1 from coming back
- Wipe the cooking space clean after use, with the microwave cool and switched off.
- Run the microwave with food or water inside, not empty.
Technical reference
- Code
- F4E1
- Appliance
- Whirlpool microwave
- Control family
- Whirlpool over-the-range microwave cavity thermistor
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Whirlpool models that can show F4E1
Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.
Related Whirlpool microwave error codes
F4E1 questions
Does F4E1 mean what F4 E1 means on a built-in?
No. The spaced code F4 E1 belongs to built-in microwaves and involves a microwave sensor and an appliance manager board. The unspaced F4E1 here belongs to over-the-range models and concerns the cavity thermistor.
Is F4E1 related to F3C?
Whirlpool's list for over-the-range models mentions the cavity temperature thermistor under both codes. Which circuit your control is reporting is something we verify at the unit.
May I carry on using the microwave?
Yes, as long as the display stays clear after the reset and the microwave behaves normally. If F4E1 returns, put the microwave out of use, since the control is unable to read the temperature in the cooking space.
Does F4E1 mean the microwave is overheating?
Not by itself. The code says the control has trouble with the thermistor reading or its wiring. Whether the cavity is actually too hot cannot be told from the code, so the circuit is tested.
What details should I note for the technician about F4E1?
Write down the model number from the label, what the display showed, and whether the reset cleared the code for any time. Those notes point us to the thermistor circuit quickly.
Need help with F4E1?
We trace the cause in your home first and write the price down before any part is swapped.
