(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool Over-the-Range Microwave E63: Another Sensor Short Code

E63 on a Whirlpool over-the-range microwave points to a shorted oven sensor circuit, with the same guidance as E62. Responsibility may sit with the sensor, the wiring or the control board.

Needs attention soonChecked November 2026

What does Whirlpool microwave code E63 mean?

Whirlpool over-the-range microwaves such as the WMH31017HS, WMH32519HZ and WMH53521HZ display E63 when the control board sees the oven sensor circuit as shorted. The guidance for E63 matches E62, so there is no hint that a different part is at work. Possible sources are the sensor, the appliance control board and the wiring. With E63 showing, a regular cooking cycle may not run.

E63 at a glance

Code
E63
Appliance
Whirlpool microwave
Applies to
Whirlpool over-the-range microwave family, WMH32519HZ
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
An oven sensor that has shorted internally

What you may notice with E63

  • E63 sits in the display of the microwave.
  • A regular cooking cycle may not run.
  • The display looks the same as it would for E62.

How the microwave detects E63

Wiring carries the oven sensor's signal to the control board, and the board expects a reading in a sensible range. When the signal collapses, as if the sensor's two conductors had joined, the board registers a shorted circuit and raises E63.

The manufacturer's guidance for E63 is the same as for E62. No second part is hinted at, so the display tells nothing more than the first code does. The short could sit in the sensor, in a harness with pinched or damaged insulation, or on the board. Because the board sees only the result, it cannot say where the short lies. It halts the cycle or declines to start, and the display carries E63 until the circuit reads correctly.

Likely causes of E63

  • An oven sensor that has shorted internally
  • Shorted or pinched wiring
  • A control board that misreads the sensor signal

Can you keep using the microwave with E63?

If E63 comes back after a reset, leave the microwave off. A shorted sensor circuit leaves the control unable to read the sensor, and the wiring that caused it can be a heat concern. If a reset clears the code and a short cycle runs normally, you may use it carefully. Switch off the breaker at any burning smell.

What you can safely check

  1. Stop the cycle; with a burning smell, switch the breaker off, keep the door shut.
  2. Keep the breaker off for a minute, then switch it back on.
  3. Stay beside the unit for a minute to be sure E63 does not return.
  4. If the display is clear, run a short cycle.
  5. Should E63 show up again, keep the microwave off and call us.

What our technician does for E63

  • A circuit test shows if the sensor, harness or board is producing the short
  • Measure the sensor path rather than assuming which code means which part
  • Keep the board for last

How to keep E63 from coming back

  • Leave a little clearance behind and around the microwave so the cord and wiring are not squeezed.
  • Do not use the microwave to support heavy items that press down on the cabinet around it.

Technical reference

Code
E63
Appliance
Whirlpool microwave
Control family
Whirlpool over-the-range microwave family, WMH32519HZ
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

Models

Whirlpool models that can show E63

Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.

FAQ

E63 questions

Why does a shorted sensor have two different codes?

The manufacturer lists E62 and E63 with identical shorted-circuit wording, so the two are treated as one area. The testing is the same for both.

Does E63 call for a new microwave?

No, not on this code alone. A short may come from just one sensor or wire, so the cause is found first, and replacing the unit is weighed only if repair makes little sense.

Does E63 need different tests from E62?

No. Both describe the same shorted oven sensor circuit, so the sensor, harness and board are examined in the same way for either code.

Is E63 more serious than E62?

No. The guidance for the two codes is the same, so they describe the same shorted oven sensor circuit. Neither is ranked above the other, and both call for the same tests.

What happens if E63 is left alone?

The microwave may keep refusing to start or stopping cycles. Because damaged wiring can worsen, it is wiser to have the circuit tested than to keep resetting the oven.

Need help with E63?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair