Whirlpool Microwave Code E62: Oven Sensor Circuit Short
E62 means the oven sensor circuit of a Whirlpool over-the-range microwave appears shorted. The sensor, the wiring or the control board may be responsible, and the oven may stop or refuse to start.
What does Whirlpool microwave code E62 mean?
E62 shows on Whirlpool over-the-range microwaves, WMH31017HS, WMH32519HZ and WMH53521HZ among them, when the oven sensor circuit looks shorted to the control board. The reading collapses instead of breaking, as though two conductors were touching. Responsibility could lie with the sensor, the wiring around it or the control board itself. With E62 on the display, a cycle may be halted, or a new one refused.
E62 at a glance
- Code
- E62
- Appliance
- Whirlpool microwave
- Applies to
- Whirlpool over-the-range microwave, model WMH31017HS
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- An oven sensor with an internal short
What you may notice with E62
- E62 appears in the display of the microwave.
- The oven stops a cycle or declines to start one.
- The code may disappear after a reset and return later.
How the microwave detects E62
The oven sensor's signal reaches the control board through wiring, and the board interprets the value it receives as a reading. A short changes that value drastically: instead of a proper reading, the board sees the signal collapse, exactly as though the two conductors had met.
That is what E62 reports. The short may sit inside the sensor, along the harness where insulation has worn or a wire has been pinched, or in the board's own circuit. Since the board only sees the final collapsed reading, it cannot locate the short. It stops the cycle or refuses to start one, because heating while blind to the sensor is not acceptable. The display carries E62 to show the control has found the sensor circuit shorted.
Likely causes of E62
- An oven sensor with an internal short
- Wiring or insulation damage that lets conductors touch
- A control board input that reads the sensor wrongly
Can you keep using the microwave with E62?
If E62 returns, stop restarting the oven and switch off the breaker. A shorted sensor circuit means the control cannot read the sensor, and damaged wiring can be a heat concern in its own right. If a reset clears the code and short cycles run normally, use the microwave sparingly and stay alert. Smell or smoke means stop at once.
What you can safely check
- Stop the cycle; at a burning smell, kill the power at the breaker and keep the door shut.
- Leave the breaker off for a minute, then switch it on.
- Give it a minute and see whether E62 appears again.
- Try a brief cycle to check normal running.
- A returning E62 means: stop restarting, and call us.
What our technician does for E62
- Test the sensor and trace the wiring for a short
- Check the sensor reading inside the harness and at the sensor
- Examine the control board's reading last so it is not replaced without need
How to keep E62 from coming back
- Keep the microwave from being pushed hard against the wall, where wiring behind it can be pinched.
- Do not pull cords or wiring you can see near the vents; leave anything behind the panels alone.
Technical reference
- Code
- E62
- Appliance
- Whirlpool microwave
- Control family
- Whirlpool over-the-range microwave, model WMH31017HS
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Whirlpool models that can show E62
Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.
Related Whirlpool microwave error codes
E62 questions
How should I understand a shorted sensor circuit?
Picture the circuit's two sides touching each other, which the control reads as a collapsed signal. The cause may be the sensor, a harness or the board, and testing finds out which.
Is E62 different from E63?
Not according to the guidance, which words E62 and E63 the same way: a shorted oven sensor circuit. The same area is examined for either code.
Can an older microwave still be repaired for E62?
Yes, an older over-the-range microwave can be repaired when the cause is a single sensor or wire. Before you decide, we say honestly if repair is sensible for your unit.
Why check the wiring before the board?
A short is more likely to come from a pinched or rubbed wire or from the sensor than from the board. The board's reading is examined last, so it is not replaced without need.
What should I mention about E62?
Tell us if the code appeared during a cycle or at start-up, whether a reset cleared it, and whether you noticed any smell. Include the model, such as WMH31017HS, if that is yours.
Need help with E62?
We trace the cause in your home first and write the price down before any part is swapped.
