(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool Over-the-Range Microwave E61: Open Oven Sensor Circuit

E61 means a Whirlpool over-the-range microwave sees an open oven sensor circuit. The control cannot complete the reading path, and the sensor, control board or wiring may be responsible.

Needs attention soonChecked November 2026

What does Whirlpool microwave code E61 mean?

Whirlpool over-the-range microwaves like the WMH31017HS, WMH32519HZ and WMH53521HZ can show E61 when the oven sensor circuit looks open to the control board. In effect the control cannot complete the path that reads the sensor, as though a wire had slipped out. Responsibility could sit with the wiring, the sensor or the appliance control board. With E61 in the display, the oven may not begin a cycle or may end one early.

E61 at a glance

Code
E61
Appliance
Whirlpool microwave
Applies to
Whirlpool over-the-range microwaves, oven sensor circuit
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
An oven sensor that has stopped passing its reading

What you may notice with E61

  • The display shows E61 in place of the normal screen.
  • The oven will not start a cycle.
  • A cycle that did start ends earlier than expected.

How the microwave detects E61

The oven sensor feeds the control board a reading that helps manage heating. The reading travels through wiring, and the circuit has to be closed from end to end for the board to receive anything.

E61 appears when the board checks the circuit and finds it open. Picture a wire that has come out of its connector, a sensor whose internal path has broken, or a board input that has stopped responding. All three look identical from the board's side, because nothing comes back. Without a sensor reading it cannot manage heating safely, so it declines to start a cycle or ends one early, and the display shows E61 to explain why the oven has stopped.

Likely causes of E61

  • An oven sensor that has stopped passing its reading
  • An open wire or a connector that has come loose
  • A control board that cannot read the sensor

Can you keep using the microwave with E61?

If a reset clears E61 and a cup of water heats normally, the microwave can be used again with care. If the code returns, stop using the oven. Without a working sensor reading, the control cannot manage heating properly, so repeated restarts are not wise. Switch off the breaker if you ever notice a burning smell.

What you can safely check

  1. Stop the cycle; at any burning smell, shut off the breaker and leave the door closed.
  2. Keep the breaker off for a minute and then restore it.
  3. Watch the microwave for a minute to confirm E61 stays gone.
  4. Warm a cup of water for a short time and see that it heats.
  5. Should the code come back, leave the oven unused and call us.

What our technician does for E61

  • Test the circuit to tell a loose connector from a failed sensor
  • Check the wiring for an open connection
  • Check the control board's reading last

How to keep E61 from coming back

  • Keep the vents above and below the microwave free of blockage so heat does not stress the sensor wiring.
  • Avoid knocking or pulling on the microwave, since a connector shaken loose can reopen the circuit.

Technical reference

Code
E61
Appliance
Whirlpool microwave
Control family
Whirlpool over-the-range microwaves, oven sensor circuit
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

Models

Whirlpool models that can show E61

Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.

FAQ

E61 questions

Which sensor does E61 refer to?

The oven sensor, which the control watches while it manages heating. With E61 the path to that sensor looks open, so no reading arrives, and a connection may be broken somewhere along it.

Do E61 and E62 describe the same thing?

Not quite, they are opposites. An open sensor circuit gives E61, a shorted one gives E62, yet both sit in the same area, so the same part of the oven is tested for either.

Is a reset enough to settle E61?

A reset may clear a one-time glitch. If E61 returns, something in the circuit needs repair, and testing comes before any part is changed.

Can a loose connector alone cause E61?

Yes. An open reading can come from a loose connector, a failed sensor or the board input, and the control reports all three the same way. Testing the circuit tells them apart.

Why would E61 come and go?

If the code is intermittent, it points to a connection that moves, such as a connector that sits loosely and makes contact only part of the time.

Need help with E61?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair