(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool Microwave Error F4 E3: Exhaust Air Temperature Sensor

Whirlpool built-in microwaves and drawers show F4 E3 when the exhaust air temperature sensor, which follows the heat of the air coming out of the microwave section, or its wiring gives the control trouble.

Stop using it until checkedChecked November 2026

What does Whirlpool microwave code F4 E3 mean?

Trouble with the exhaust air temperature sensor or the wires attached to it brings up F4 E3 on Whirlpool built-in microwaves and drawers, model WMC50522AS included. That sensor reports the heat of the air coming out of the microwave section, and the control relies on the figure to avoid overheating. Whirlpool's only listed step is a power reset, so we regard F4 E3 as a sensor circuit awaiting a test.

F4 E3 at a glance

Code
F4 E3
Appliance
Whirlpool microwave
Applies to
Whirlpool built-in microwave exhaust sensor, WMC50522AS
Type
Stop using it until checked
Can you clear it yourself?
No, stop using it until it is checked
Most likely cause
Exhaust air temperature sensor in the microwave section

What you may notice with F4 E3

  • F4 E3 appears and the microwave section stops its usual cycles
  • The oven refuses normal operation while the code shows
  • The code may return soon after power is restored

How the microwave detects F4 E3

Air moves through a built-in microwave while it works, and it leaves the microwave section carrying heat. A sensor in that exhaust path measures how warm the air is and sends the reading to the control through a plug and wiring.

The control compares the reading with what it considers acceptable for the section. When the sensor, its lead or the board input stops giving a reading the control accepts, F4 E3 appears and normal running stops. Because this sensor exists to guard against overheating, the control treats the code seriously. Whirlpool's listed step is to cut power and restore it, which makes the control read the sensor from scratch. A healthy circuit lets the display clear. A circuit with a problem sends F4 E3 back, and the oven should wait for a proper test.

Likely causes of F4 E3

  • Exhaust air temperature sensor in the microwave section
  • Plug or wire damage on the sensor lead
  • Control board input that reads the sensor

Can you keep using the microwave with F4 E3?

No, not while F4 E3 is showing. The sensor behind this code protects the microwave section from running too hot, so cooking with the circuit unproven is a gamble. Whirlpool's reset is fair to try once, with the vents clear. If the display stays clear and a short cycle behaves, use the oven with care and note the date. If the code returns, leave the microwave off at the breaker until the sensor circuit has been tested.

What you can safely check

  1. Leave the microwave unused, let it cool, then switch off its breaker.
  2. While it is off, look at the vents and the space around the unit and clear away anything pressed against it.
  3. After a minute restore power and watch the display for another minute.
  4. If the code stays away, a short cycle is a reasonable trial.
  5. If F4 E3 shows again, keep the oven off and call us.

What our technician does for F4 E3

  • Read the exhaust sensor circuit and compare it with what the control expects
  • Inspect the plug and lead at the sensor
  • Test the control input before the oven is allowed to run again

How to keep F4 E3 from coming back

  • Keep the vents of the microwave clear and leave open space around the unit so air can leave freely.
  • Wipe grease and dust from the vent openings when the oven is cool and switched off.

Technical reference

Code
F4 E3
Appliance
Whirlpool microwave
Control family
Whirlpool built-in microwave exhaust sensor, WMC50522AS
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F4 E3 questions

What is the exhaust air sensor watching?

How hot the exhaust air is as it comes out of the microwave section. The control uses that figure to keep the section from running hotter than it should, so F4 E3 means that safeguard cannot be trusted.

Why do you handle F4 E3 more cautiously than most sensor codes?

Because the sensor exists to protect against running hot. Whirlpool gives no safety warning, yet using the oven with an unverified sensor is a risk we would rather you avoid.

Can blocked ventilation produce F4 E3?

Whirlpool lists no such cause. Clearing the vents and the space around the unit is still sensible before the reset, though a code that returns calls for a test of the sensor circuit.

Is F4 E3 the same as the other F4 E codes?

They belong to one family and share a reset, but each names its own part. F4 E3 names the exhaust air temperature sensor, so its first checks differ from the codes for the inverter or the humidity sensor.

Will F4 E3 clear without help?

A reset may clear the display, but if the sensor circuit still has a problem the code returns. A repeat, especially soon after the reset, is the cue to test the circuit instead of resetting again.

Need help with F4 E3?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair