Whirlpool Microwave Code F4 E2: Thermistor or Sensor Circuit
F4 E2 on a Whirlpool built-in microwave or drawer points the control's complaint at the microwave sensor or thermistor, the appliance manager, or the wiring, telling us where to test.
What does Whirlpool microwave code F4 E2 mean?
Whirlpool lists F4 E2 for its built-in microwaves and drawers, with WMC50522AS as an example. The code names the microwave sensor or thermistor, the appliance manager that runs the microwave side, or the wiring joining them. On the display, F4 E2 means the control thinks something in that sensor circuit is off. The guidance gives a power reset and no failed part, so we take the code as a place to test and not a part to replace.
F4 E2 at a glance
- Code
- F4 E2
- Appliance
- Whirlpool microwave
- Applies to
- Whirlpool built-in microwave sensor circuit, WMC50522AS
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- Microwave-side sensor or thermistor reading incorrectly
What you may notice with F4 E2
- F4 E2 appears on the display
- The microwave does not carry on as it normally does
- The display may clear after a reset and the code return later
How the microwave detects F4 E2
On the microwave side of a built-in oven, a sensor or thermistor feeds a reading to the appliance manager board through a wire harness. The board uses that reading to decide how the microwave section should behave, and it expects the reading to stay within a believable range.
F4 E2 is shown when the control decides that the reading, the board or the harness is not trustworthy. The display does not say which of the three is responsible, so the code works as a pointer to the sensor circuit. Whirlpool's reset restarts the control. A clear display afterward does not prove the circuit is healthy, because a weak connection can behave for a while. If F4 E2 comes back, the circuit is measured and compared with what the board expects.
Likely causes of F4 E2
- Microwave-side sensor or thermistor reading incorrectly
- Appliance manager board that interprets the reading
- Wire harness carrying the signal between them
Can you keep using the microwave with F4 E2?
Only while the display stays clear. A microwave unable to rely on its own sensor is a poor one to keep running, even though the brand gives no safety warning for F4 E2. After one reset and a brief normal cycle, you can use it with care. If the code returns, stop using the oven until the sensor circuit has been tested.
What you can safely check
- With the oven idle, turn the microwave's breaker off.
- Keep it off for sixty seconds, then restore power.
- Look for F4 E2 on the display over the next minute.
- If it stays clear and a brief cycle runs normally, the oven is working.
- If F4 E2 returns, it needs a sensor circuit test, so call us.
What our technician does for F4 E2
- Measure the sensor circuit
- Compare the measurement with what the board expects
- Check the harness and replace only what proves to be the cause
How to keep F4 E2 from coming back
- Wipe splashes out of the cavity promptly, with the oven off and cool, to keep residue away from the sensor area.
- Report a code that comes and goes soon after it first appears, instead of waiting.
Technical reference
- Code
- F4 E2
- Appliance
- Whirlpool microwave
- Control family
- Whirlpool built-in microwave sensor circuit, WMC50522AS
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool microwave error codes
F4 E2 questions
Is there a reason the display reads F4 E2 rather than F4 E1?
The two codes share the same list of areas in the guidance, with no separate meaning given for either. Only a test on the oven reveals which circuit the control has in mind.
Is it risky to run the microwave with F4 E2?
Whirlpool gives no safety warning for this code. Still, a microwave that cannot rely on its own sensor is not one to keep using, so stop if the code returns.
Which details help most when I phone about F4 E2?
Your model label, the code wording on the display, and whether a reset cleared it for any time at all.
Can the display look fine while the circuit still has a problem?
Yes. A reset that clears the display proves little about the sensor circuit, because a weak connection can behave for a while and then drop out. A repeat is the reason for a proper test.
Does the time F4 E2 stays away matter?
It can. A code that stays gone for weeks suggests the reset cleared a passing condition, while one that returns within days suggests a connection or sensor with a real problem. Note the dates for us.
Need help with F4 E2?
We trace the cause in your home first and write the price down before any part is swapped.