Whirlpool Built-in Microwave Showing PUSH or PSH: Press Start
PUSH or PSH appearing on a Whirlpool built-in microwave is a reminder to press Start; the setup waits, and it is dropped if Start never comes.
What does Whirlpool microwave code PUSH or PSH mean?
A Whirlpool built-in microwave or drawer, the WMC50522AS for instance, shows PUSH or PSH to tell you to press Start, the pad that begins every oven function. Leave it unpressed for five seconds after setting a function and the reminder appears. When a minute goes by after a keypad press and Start still has not been pressed, the oven drops the function and shows the time of day again. That is normal behavior and no malfunction.
PUSH or PSH at a glance
- Code
- PUSH or PSH
- Appliance
- Whirlpool microwave
- Applies to
- Whirlpool WMC50522AS built-in microwave, Start reminder
- Type
- Normal status, not a failure
- Can you clear it yourself?
- Yes, it is a normal message or setting
- Most likely cause
- Start was not pressed after a function was entered
What you may notice with PUSH or PSH
- PUSH or PSH appears a few seconds after you set a function
- Nothing runs until Start is pressed
- The time of day returns if you wait too long
How the microwave detects PUSH or PSH
Programming a microwave takes two actions. You enter the settings, such as a mode and a time, and then you confirm with Start, the pad that actually begins any oven function. Until Start is pressed, the control keeps everything ready but runs nothing.
After five seconds without a Start press, the control shows PUSH or PSH to nudge you. The nudge does not last forever. When a minute passes following a keypad press with still no Start, the control abandons the half-finished entry and goes back to the time of day. All of this is designed behavior, so the display is guiding you rather than reporting damage.
Why PUSH or PSH appears
- Start was not pressed after a function was entered
- The Start pad is not responding to presses
Can you keep using the microwave with PUSH or PSH?
Yes, the microwave is fine to use. PUSH or PSH is only a reminder to press Start, and it raises no safety concern. If Start itself seems unresponsive, use the microwave cautiously and have the keypad checked, since a pad that ignores presses could also act up at other moments.
What you can safely check
- Nothing about the power needs touching, since the supply is not the problem.
- Set the function you want.
- Tap Start soon afterward, within five seconds of finishing.
- If the reminder still shows after you pressed it, press the pad again with some force.
- If the pad seems dead, cut power at the breaker for a minute and restore it, and contact us if that fails.
What our technician does for PUSH or PSH
- Test the Start pad and its connection when a press does nothing
- Check how the control reads that pad
How to keep PUSH or PSH from coming back
- Make Start the last pad you press every time, so the reminder has no reason to appear.
- Keep the keypad clean and dry, because grease or moisture can make a pad feel unresponsive.
Technical reference
- Code
- PUSH or PSH
- Appliance
- Whirlpool microwave
- Control family
- Whirlpool WMC50522AS built-in microwave, Start reminder
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool microwave error codes
PUSH or PSH questions
Does PUSH point to a broken part?
No, it just reminds you to press Start. The setup waits for that press and is dropped after a minute without one. Press Start soon after you enter settings and the reminder never shows.
Why did the oven drop my settings?
Start did not come within a minute of the last keypad press, so the oven went back to the time of day. This stops it sitting half-programmed, and you just enter the settings again.
Start does nothing when I press it. What next?
Press harder and reset the breaker for a minute. When the pad still fails to respond, the keypad may need testing, which we can do.
Is there a way to switch the PUSH reminder off?
Nothing in the guidance describes one, since the reminder is part of normal behavior. Pressing Start after entering a function is the simple way never to see it.
Could PUSH appear even though I pressed Start?
It can if the pad did not register the press. Pressing again firmly generally settles it, and if the pad keeps missing presses, the keypad or its connection should be tested.
Something else going on with your microwave?
We trace the cause in your home first and write the price down before any part is swapped.