Whirlpool Range BadLine Message: Power Wired Incorrectly
Bad Line on a Whirlpool range means power is applied but not wired correctly. Switch the range off at the breaker and have a qualified electrician or the installer correct the supply wiring.
What does Whirlpool range code BadLine mean?
Whirlpool documents the Bad Line display as power being applied but not wired correctly. On a range, that is a supply wiring message. The range is receiving power in a way the control does not accept, such as a terminal block wired incorrectly or a neutral or ground connection that is missing or loose. It most often follows an installation, a move, or work on the outlet or terminal block. The control refuses to run because incorrect supply wiring on a 240 volt appliance is a shock and fire risk.
BadLine at a glance
- Code
- BadLine
- Appliance
- Whirlpool range
- Applies to
- Whirlpool electric ranges, 240 volt supply
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- Terminal block wired incorrectly during installation
What you may notice with BadLine
- Bad Line appears on the display
- The range will not heat or run
- The message appeared right after installation or a move
- Work on the outlet or cord happened recently
How the range detects BadLine
An electric range expects a specific arrangement at its supply connection: two live legs, a neutral and a ground, all landing on the right terminals. When power reaches the control, it also checks that these connections look the way it expects.
Bad Line is the control's way of reporting that power is present but the arrangement is wrong. A terminal block wired incorrectly, a neutral or ground that is missing or loose, or an outlet wired differently from the range's needs can each make the supply look wrong. The control stops, because running a 240 volt appliance on incorrect wiring risks shock and fire. This is a message about the supply, so nothing at the panel can fix it.
Likely causes of BadLine
- Terminal block wired incorrectly during installation
- Neutral or ground connection missing or loose
- Outlet wired incorrectly
- Supply cord or its connection damaged
Can you keep using the range with BadLine?
No. Do not use the range while Bad Line shows. Incorrect supply wiring on a 240 volt appliance is a shock and fire risk, and trying the range again to see what happens only raises it. Keep the breaker off until a qualified electrician or the installer has checked and corrected the wiring. After that, we can test the range itself if anything still looks wrong.
What you can safely check
- Switch the range off at the breaker now and leave the breaker off.
- Do not open the rear panel, touch the terminal block or re-seat the plug to see what happens.
- Note whether the range was recently installed, moved, or had work done on the outlet.
- Call a qualified electrician or the installer, and call us if the range itself needs testing afterward.
What our technician does for BadLine
- Check the supply connection at the range against the wiring requirements
- Inspect the terminal block and supply cord for damage
- Confirm neutral and ground connections once the outlet is corrected
- Test the control after the supply is made right
How to keep BadLine from coming back
- Have a qualified electrician or the installer connect the supply when a range is installed or moved.
- Do not swap cords or outlets without checking the range's wiring requirements.
- After any outlet work, make sure the range starts normally before relying on it.
Technical reference
- Code
- BadLine
- Appliance
- Whirlpool range
- Control family
- Whirlpool electric ranges, 240 volt supply
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool range error codes
BadLine questions
Can I fix Bad Line by resetting the range?
No. A reset does not change how the supply is wired. The message points to the connection itself, so the range should stay off at the breaker until a qualified person checks it.
Why does Bad Line appear after a new install?
A fresh install or a move is the most likely moment for a wiring mistake, such as a miswired terminal block or a missing neutral or ground. The installer or an electrician should go back and correct it.
Is Bad Line dangerous?
Incorrect supply wiring on a 240 volt appliance is a shock and fire risk, so yes, treat it seriously. Keep the breaker off and do not try the range again until it is checked.
Is Bad Line a problem with the range or the house?
Usually the supply, meaning the cord, terminal block or outlet, rather than the range itself. Once the wiring is corrected, the message should go away. If it does not, the control needs a test.
What should I tell you about Bad Line?
Tell us when the range was installed or moved, who did the wiring, and whether anything was changed at the outlet. That tells us whether to start with the supply or the range.
Need help with BadLine?
We trace the cause in your home first and write the price down before any part is swapped.