Whirlpool Dishwasher F6E3 Error: Too Much Foam Inside the Tub
Whirlpool built-in dishwashers like the WDF520PADM show F6E3 when the suds sensing finds foam in the tub. A common cause is the wrong soap or too much detergent.
What does Whirlpool dishwasher code F6E3 mean?
Whirlpool built-in dishwashers, such as the WDF520PADM, raise F6E3 when foam collects in the bottom of the tub. The suds sensing system picks up the foam and may keep the dishwasher from filling or running normally. Wrong soap is a frequent trigger: laundry detergent, hand soap, or dish detergent meant for hand washing all foam heavily, and so does a heavy pour of the right product. You will see the code, and the cycle stops or will not begin.
F6E3 at a glance
- Code
- F6E3
- Appliance
- Whirlpool dishwasher
- Applies to
- Whirlpool built-in dishwashers such as the WDF520PADM
- Type
- Maintenance reminder
- Can you clear it yourself?
- Usually, once the care step is done
- Most likely cause
- The wrong type of soap, such as hand soap or laundry detergent
What you may notice with F6E3
- Foam or suds sits in the bottom of the tub
- F6E3 appears on the dishwasher display
- The cycle halts or the dishwasher will not start
- Soap that was not made for dishwashers went in
How the dishwasher detects F6E3
A dishwasher fills, washes and drains in steps, and the control wants to know what the water is doing at each stage. A suds sensing system watches the bottom of the tub for foam. Soap that is meant for dishwashers produces little foam in the spray, but hand soap, laundry detergent or a heavy pour of the right detergent can fill the tub with suds. Once that foam reaches the sensor, the control raises F6E3 and may keep the dishwasher from filling or running as it should.
The code therefore starts as a cleaning problem, not a parts problem. Removing the foam and running an empty wash normally settles it. If a clean tub and the right detergent still bring the code back, the sensing itself, or how the control reads it, becomes the question.
Why F6E3 appears
- The wrong type of soap, such as hand soap or laundry detergent
- A heavy pour of detergent, or rinse aid left behind
- Foam left sitting in the tub after the previous cycle
- A suds-detection reading that stays wrong even with a clean tub
Can you keep using the dishwasher with F6E3?
Yes, once the foam is gone and you are using the right detergent. Scoop out the suds, wipe the tub, run one empty wash and then a normal load. If F6E3 comes back with a clean tub, stop running cycles and have us test the suds sensing, since the dishwasher may be misreading what is inside.
What you can safely check
- End the cycle and cut power at the breaker, or pull the plug, before reaching into the tub.
- Check the tub floor for foam.
- Scoop out the suds with a cup or cloth and wipe the area dry.
- From now on, load only a detergent designed for automatic dishwashers, and measure the amount.
- Run an empty wash with no dishes and no detergent, then try a normal load.
- If F6E3 shows up again with a clean tub, call us.
What our technician does for F6E3
- Test the suds sensing and what it reads in a clean tub.
- Check how the water level behaves during the fill.
- Judge if the foam was genuine or the sensing misread it.
How to keep F6E3 from coming back
- Keep hand soap, laundry detergent and dish soap for hand washing away from the dishwasher.
- Measure detergent for each load instead of filling the cup because the dishes look dirty.
- Wipe away leftover rinse aid residue if suds keep appearing, so it does not add to the foam.
Technical reference
- Code
- F6E3
- Appliance
- Whirlpool dishwasher
- Control family
- Whirlpool built-in dishwashers such as the WDF520PADM
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Whirlpool models that can show F6E3
Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.
Related Whirlpool dishwasher error codes
F6E3 questions
Why does hand soap cause F6E3?
Hand-wash soap foams far more than automatic dishwasher detergent, and the suds sensing reacts to that foam. Laundry detergent behaves the same way, so keep both away from the dishwasher.
Can too much of the correct detergent trigger it?
Yes, a heavy pour can foam enough to set off the sensing. Measure the amount instead of guessing, and avoid adding extra because the load looks large.
What if foam keeps coming back after I clean the tub?
Then something besides soap may be involved, such as leftover residue or a sensing reading that is off. If a clean tub and proper detergent still produce F6E3, the sensing needs testing.
Is F6E3 the same as a leak or water supply problem?
No. F6E3 concerns foam in the tub, not a leak or a supply problem. Other codes cover those, so look for suds first and tell us what you see if the code stays.
Does the code mean something is broken?
Not at first. Foam from the wrong soap or too much detergent is a common reason, and it clears once the tub is cleaned and the right detergent is used. A returning code is when testing makes sense.
Something else going on with your dishwasher?
We trace the cause in your home first and write the price down before any part is swapped.
