(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool Built-In Microwave Code 1d11: Temperature Sensor Circuit

Whirlpool built-ins and drawers show 1d11 when the sensor that reads oven temperature, the control or the wiring between them is in question. It names where to look, not one failed part.

Needs attention soonChecked November 2026

What does Whirlpool microwave code 1d11 mean?

Code 1d11 involves three things at once on Whirlpool built-ins and drawers such as the WMC50522AS: the oven temperature sensor, the control and the wiring between them. Because it describes a circuit, it names where to look instead of one failed part. Cooking steps that depend on temperature sensing may stop or be switched off while the code is up, until the oven reads normally again.

1d11 at a glance

Code
1d11
Appliance
Whirlpool microwave
Applies to
Whirlpool built-in microwaves with oven temperature sensing
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Temperature sensor giving a reading outside what the control expects

What you may notice with 1d11

  • 1d11 appears on the oven display
  • Temperature-based cooking may stop or be unavailable
  • The oven reads normally again only after the code clears

How the microwave detects 1d11

A microwave that cooks by temperature needs a sensor to report how hot things are, and the oven control reads that report many times as a cycle runs. The control expects the reading to stay within a believable range and to arrive over intact wiring. When it does not, the control raises 1d11 and may disable the functions that depend on temperature.

Because three things are involved, the sensor, the control and the wiring between them, the code alone cannot say which one is responsible. A reading that is out of range may be the sensor drifting, or it may be the control misjudging it, or a connection that has weakened. A passing glitch is possible too. Restarting at the breaker rules that out, and a returning code sends the sensor and control to separate tests.

Likely causes of 1d11

  • Temperature sensor giving a reading outside what the control expects
  • Oven control flagging a problem in the sensor circuit
  • Wiring or connector joining the sensor to the control
  • A short glitch that a power cycle clears

Can you keep using the microwave with 1d11?

Do not rely on temperature-based cooking while 1d11 shows, because the oven cannot read heat correctly and may stop. After a reset clears the code, short watched use is reasonable. If the code returns, leave the microwave off at the breaker rather than cooking with a sensor you cannot trust, and keep out of the cabinet.

What you can safely check

  1. Switch the microwave's breaker off and keep it off for a full minute.
  2. Restore the power at the breaker.
  3. Keep the oven in view for a minute to see if 1d11 comes back.
  4. If it stays away, run a short cooking test to see that the oven works.
  5. If the code returns, stop using the oven and call us.

What our technician does for 1d11

  • Test the temperature sensor and the control separately
  • Check the wiring and connectors in the same visit
  • Replace only the part that fails its test, with the price in writing first

How to keep 1d11 from coming back

  • Keep steam, grease and splashes off the control area of a built-in unit, so moisture stays away from the wiring.
  • Avoid covering vents or stacking items against the unit, which can leave the oven's electronics in trapped heat.

Technical reference

Code
1d11
Appliance
Whirlpool microwave
Control family
Whirlpool built-in microwaves with oven temperature sensing
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

1d11 questions

Does 1d11 prove that the sensor has gone bad?

Not necessarily, since three parts share this code: the sensor, the control and the wiring between them. Resetting the breaker can wipe out a passing glitch, and if the code returns, each part is tested one at a time.

Is it all right to run the microwave with 1d11 displayed?

While the code is displayed, cooking steps that need temperature sensing may be blocked. Try one reset, then leave the oven off until it has been checked.

Is an older built-in microwave worth repairing?

Sometimes. The repair cost is set against the value of the unit, and you get an honest answer if replacing it would make more sense.

Is 1d11 the same as the other 1c codes?

No. The 1c codes name the oven control or the keypad circuit, while 1d11 brings the temperature sensor into the picture along with the control and the wiring. Read the exact characters on your display.

Will 1d11 clear by itself?

A short glitch can clear after a restart, but a real sensor, control or wiring problem will not. If the code is back after the one-minute reset, the sensor circuit needs to be tested.

Need help with 1d11?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair