(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool Built-In Microwave F1 E6: Thermistor or Sensor Reading

A built-in Whirlpool microwave or drawer displaying F1 E6 is pointing at its thermistor or sensor, or the wiring tied to it. The code names a circuit to test, not a sensor already proven bad.

Needs attention soonChecked November 2026

What does Whirlpool microwave code F1 E6 mean?

Whirlpool built-in microwaves and drawers, WMC50522AS among them, display F1 E6 when the control reports trouble that may involve the microwave's thermistor or sensor, or the wiring attached to it. A thermistor senses temperature, and the control relies on it to stay within safe limits. The oven may halt or refuse a start while the code is displayed. Treat the code as naming a circuit to test rather than a sensor already proven bad.

F1 E6 at a glance

Code
F1 E6
Appliance
Whirlpool microwave
Applies to
Whirlpool built-in microwave thermistor circuit, WMC50522AS
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
The microwave thermistor or sensor

What you may notice with F1 E6

  • A message of F1 E6 replaces the normal display.
  • The oven may halt or refuse to begin a cycle.
  • The code may show again after a power reset.

How the microwave detects F1 E6

A thermistor is a tiny part whose electrical resistance shifts as it warms or cools. The control passes a small signal through it and reads the result as a temperature, which lets the microwave stay inside safe limits while it heats.

F1 E6 appears when the control reports trouble with that reading. The thermistor could be returning a wrong value, the wiring or connector could be breaking up the signal, or the control could be misreading a healthy sensor. The display cannot separate these. If the reading drifts only as the oven heats, the cause leans toward a connection or part that responds to heat. Without a temperature it can trust, the control will not heat, so the oven may halt or refuse to begin.

Likely causes of F1 E6

  • The microwave thermistor or sensor
  • Wiring and the connector at the sensor
  • The control reading the sensor signal

Can you keep using the microwave with F1 E6?

If a reset clears F1 E6 and a brief cycle heats normally, the microwave can stay in use while you watch for a repeat. Should the code reappear, leave the oven unused and switch off its breaker. The thermistor helps the control keep heating within safe limits, so a repeating code is a reason to wait for testing.

What you can safely check

  1. Stop the cycle and let the oven cool; switch off the breaker if you notice a burning smell.
  2. Keep the breaker off for one minute and then restore power.
  3. Note whether F1 E6 stays gone during the following minute.
  4. Run a brief cycle and check that heating is normal.
  5. If the code returns, leave the oven unused.

What our technician does for F1 E6

  • Check the thermistor reading and its wiring, since either can produce the same code
  • Watch whether the reading drifts as the oven warms up
  • Show the finding and the written price before any work

How to keep F1 E6 from coming back

  • Keep the area around the microwave ventilated, since trapped heat is hard on sensors and their wiring.
  • Avoid pulling on the microwave in its opening, which can loosen the connector at the sensor.

Technical reference

Code
F1 E6
Appliance
Whirlpool microwave
Control family
Whirlpool built-in microwave thermistor circuit, WMC50522AS
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F1 E6 questions

What does a thermistor do inside a microwave?

A thermistor is a small temperature-sensitive part: its resistance shifts with heat, and the control reads that shift. F1 E6 means the reading may be wrong somewhere between the part and the control.

Is F1 E6 the same code as F1?

No. F1 points at the oven temperature sensor circuit, while F1 E6 points at the microwave thermistor or sensor, so different parts of the oven are tested.

Can a thermistor problem be repaired on an older unit?

Sensors and connectors can be reasonable repairs on older units. You get an honest answer about whether repair makes sense before any work begins.

Why would the thermistor and its wiring give the same code?

Both can leave the control without a usable temperature reading, and the control cannot see which one is responsible. That is why the thermistor reading and the wiring are both checked during testing.

Can the reading change only when the oven warms up?

Yes. A reading that drifts as the oven warms up points toward a connection or sensor affected by heat. Noting when the code appears in the cycle helps narrow it down.

Need help with F1 E6?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair