(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool Built-in and OTR Microwave Code F8E5: Exhaust Air Sensor

F8E5 shows on two Whirlpool microwave styles and points to the exhaust air temperature sensor or its wires; the unit stops, but the sensor is not proven bad.

Needs attention soonChecked November 2026

What does Whirlpool microwave code F8E5 mean?

Two Whirlpool microwave styles can show F8E5. On a built-in unit or drawer such as the WMC50522AS, the guidance names the exhaust fan air temperature sensor and its wires. Over-the-range models, the WMH31017HS, WMH32519HZ and WMH53521HZ, call the same sensor the exhaust air temperature sensor and add that the oven did not carry out the function. Either way the unit stops with F8E5 showing. Treat it as a circuit to test.

F8E5 at a glance

Code
F8E5
Appliance
Whirlpool microwave
Applies to
Whirlpool built-in and over-the-range microwave exhaust sensor
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
The sensor in the exhaust air path

What you may notice with F8E5

  • F8E5 appears on the unit's display
  • The microwave halts partway through a function
  • The message returns after a reset

How the microwave detects F8E5

A sensor placed in the exhaust path measures how warm the air leaving the microwave is. It reports to the control along its wires, giving the control a way to judge whether cooling and heating are in balance.

If that reading disappears or looks wrong, the control has nothing to rely on, so it stops the function and shows F8E5. On a built-in unit the manual names the part the exhaust fan air temperature sensor, while an over-the-range model calls it the exhaust air temperature sensor and has the oven report that it did not carry out the function. The sensor, a connector or the control input may be responsible. On an over-the-range unit the way air leaves the cabinet also matters, because the sensor reads that airflow.

Likely causes of F8E5

  • The sensor in the exhaust air path
  • Wires and plugs between the sensor and the control
  • The control input that reads exhaust temperature

Can you keep using the microwave with F8E5?

When a reset clears F8E5 and the microwave heats normally, you may use it and watch for a repeat. Once the code returns, stop and leave it off. The control relies on that exhaust reading to know whether heat is leaving, and a unit running without it is working blind. Do not try to reach the sensor, which sits behind panels.

What you can safely check

  1. If you were cooking, switch the microwave's breaker off at the panel and let the unit cool.
  2. After one minute, switch the breaker back on.
  3. Remain near the microwave for a minute and watch for the code.
  4. With a clean screen, try an ordinary cycle and see that the unit works.
  5. If F8E5 returns, stop using the microwave and phone us.

What our technician does for F8E5

  • Test the exhaust air temperature sensor circuit
  • On an over-the-range unit, look at how air leaves the cabinet
  • Decide on parts only after the signal is measured

How to keep F8E5 from coming back

  • Keep the exhaust and vent paths clear of stacked items and cabinet trim.
  • Wipe the visible vent openings when the unit is off and cool so grease does not build up there.

Technical reference

Code
F8E5
Appliance
Whirlpool microwave
Control family
Whirlpool built-in and over-the-range microwave exhaust sensor
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

Models

Whirlpool models that can show F8E5

Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.

FAQ

F8E5 questions

Is F8E5 limited to one microwave style?

No. Built-in and over-the-range units both display it, and each points at one exhaust sensor circuit. Testing that circuit tells us which part is responsible.

May I carry on after a reset?

You may when the code stays gone and heating looks right. Should F8E5 return, set the microwave aside until the sensor circuit has been tested.

Does an aging microwave showing F8E5 deserve repair?

Frequently it does, particularly with a built-in. The written price comes first, and we say plainly when replacement makes more sense. Condition counts for more than age.

Why does F8E5 differ from the built-in-only version?

Both name the same sensor on different styles of unit. The built-in version is shown on built-in units, while F8E5 can appear on built-in and over-the-range models. The circuit test is the same.

What should I mention when I phone about F8E5?

Give the exact code, the model number such as WMH31017HS or WMC50522AS, and whether the unit stopped during a cycle. Tell us if a reset cleared it, even briefly.

Need help with F8E5?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair