(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool Microwave E24 Explained: Overheat Shutdown

E24 is an overheat shutdown on a Whirlpool over-the-range microwave: the oven hit 500 degrees F (260 degrees C). It stops as protection, so do not keep restarting it.

Stop using it until checkedChecked November 2026

What does Whirlpool microwave code E24 mean?

On Whirlpool over-the-range microwaves like the WMH31017HS, WMH32519HZ and WMH53521HZ, E24 reports an overheat condition, reached at 500 degrees F (260 degrees C). Guidance lists four suspects: a thermal sensor, a gas sensor, the appliance control board, and the wiring. The oven shuts itself down and shows E24. Because the oven stopped itself to protect you, take it seriously and resist restarting the microwave repeatedly to see whether it clears.

E24 at a glance

Code
E24
Appliance
Whirlpool microwave
Applies to
Whirlpool over-the-range microwaves, e.g. WMH53521HZ
Type
Stop using it until checked
Can you clear it yourself?
No, stop using it until it is checked
Most likely cause
A false reading from the thermal sensor

What you may notice with E24

  • The oven shuts down and E24 shows in the display.
  • The cabinet area around the microwave may feel hot.
  • The oven refuses to run again until it has cooled.

How the microwave detects E24

Over-the-range microwaves keep an eye on their own temperature. The thermal sensor and the gas sensor feed readings to the control board, and the board has a ceiling it will not allow the oven to pass. That ceiling is 500 degrees F (260 degrees C).

When a reading reaches it, the control shuts the oven down and displays E24. The reading can be real, perhaps from heat that rose from a cooktop below, or false, if a sensor, a wire or the board itself has misread. The control has no means of telling which, so it treats the overheat as genuine. Shutting down first and asking questions afterward is the cautious behavior, and the display is how it tells you what happened.

Likely causes of E24

  • A false reading from the thermal sensor
  • A false reading from the gas sensor
  • A control board that misjudges the sensor signals
  • Wiring and connectors

Can you keep using the microwave with E24?

Do not keep using the microwave if E24 returns. One reset after it has fully cooled is reasonable, but repeating it only pushes the oven back toward the same limit. Should you notice burning or smoke, pull the plug or cut the breaker and leave the door closed. Leave it off until the sensors and control have been tested.

What you can safely check

  1. Stop the cycle, leave the door closed, and let the microwave cool fully before touching anything.
  2. At any burning smell or smoke, cut power at the breaker or unplug the unit and keep the door shut.
  3. After it has cooled, switch the breaker off for a minute and back on, then watch the display for a minute.
  4. Do this reset only once.
  5. A second E24 means the oven stays off; call us.

What our technician does for E24

  • Establish if the oven really overheated or a sensor gave a false reading
  • Check the thermal sensor, the gas sensor and the control board
  • Look at heat reaching the microwave from a cooktop below

How to keep E24 from coming back

  • Keep the area around the microwave clear and the vents open so heat does not build up.
  • Use the cooktop below with the vent fan running when cooking at high heat, so rising heat is carried away.

Technical reference

Code
E24
Appliance
Whirlpool microwave
Control family
Whirlpool over-the-range microwaves, e.g. WMH53521HZ
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

Models

Whirlpool models that can show E24

Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.

FAQ

E24 questions

Does E24 mean something is on fire?

No, it means the oven reached its overheat limit and shut itself down as a precaution. If you do smell burning or see smoke, cut the power at the breaker and leave the door closed.

Is it okay to reset it and carry on cooking?

A single reset after the oven has cooled is acceptable. Should E24 return, leave the microwave unused until the sensors and control have been checked, and do not repeat the reset a second time.

Can an older microwave be repaired for E24?

Yes, when the cause is a single sensor or connection, since that kind of repair can be modest. A frank comparison of repair cost against the age of the unit comes first.

Does E24 always mean the oven really got hot?

Not always. The oven may have reached the overheat condition, or a sensor, wire or the control board may have misread. That is why both possibilities are tested, and why the oven should stay off meanwhile.

What should I do if E24 appears while something is cooking?

Stop the cycle, keep the door closed and let the microwave cool. At any sign of burning or smoke, cut the power at the breaker or unplug it, and leave the door closed.

Need help with E24?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair